Sh!t We Like – TP-Link Nano Router TL-WR702N

Sh!t We Like – TP-Link Nano Router TL-WR702N

Pack your own parachute and bring your own wireless router

If you ever gave a talk or presentation that involved demonstrating software running on a wireless device, you probably remember some restlessness, approaching the venue.

What would the Wifi conditions be? Would you be able to connect your device(s) to the Wifi network? Would the bandwidth be sufficient, to support a smooth demo? etc. etc.

There is no such thing as perfect and you can never be over-prepared. The same it probably true when it come to display-adapters, especially if a MacBook is your presentation tool of choice. Pack all the Thunderbolt/MiniDisplayPort to DVI/HDMI/VGA adapters you can find. And just in case, I usually export my slides to PDF and put that file on a FAT-formatted USB-Thumb-drive. Moreover, I used to schlep a standard home-office router, together with its bulky power-supply of course. But not anymore …

I recently came across a nifty and tiny Wifi Router that is not only fast enough, but can be powered with a standard 5V phone charger, using a standard Micro-USB Cable – or even better, leeching power off a standard USB-Port (e.g., one of the MacBook’s USB-Ports).


Speedtest (ISP-Cox)

I certainly had my doubts when it came to data transfer rates, but this little guy is seriously fast. Here is a real world test, comparing the TP-Link TL-WR702N to a Cisco Linksys E4200 Wireless-N Dual-Band Wi-Fi Router, on my home network:

Speed Test w/ TL-WR702N

Speed Test w/ TL-WR702N

Speed Test w/ LinkSys E4200

Speed Test w/ LinkSys E4200

The TP-Link TL-WR702N uses the Atheros AR9331 chipset and is equipped with 2MB Flash memory and 16MB RAM, which unfortunately is not quite enough to replace the stock OS with an open-source Linux distribution for embedded devices, like OpenWrt or DD-WRT.

However, the stock software already provides some capabilities, often missing in many full-size home-network routers.
For instance, the TL-WR702N can be operated in five different modes:

AP Mode

This is the WR702N’s default mode. The nano router supplements a wired LAN (to which it connects, using an Ethernet cable) and enables its wireless clients, to connect to that LAN wirelessly.

Wireless Router Mode

The one and only wired port works as WAN Port, e.g. gets connected to a DSL/Cable Modem. The routers works as an DHCP server and wireless clients can obtain IP addresses and DNS automatically.

Repeater Mode

The TL-WR702N is used to extend the range of an existing AP or wireless router.
In this mode, the one and only wired port gets connected to a client laptop or PC via Ethernet cable. However, clients can also connect to the nano router wirelessly. The SSID of TL-WR702N should exactly match the SSID of the device you want to repeat. In Repeater Mode, the DHCP server defaults to off.

Bridge Mode

Pretty much the same as the Repeater Mode, but the the nano router’s SSID does not match any other Wifi-Router’s SSID on your network.

Client Mode

The TL-WR702N is basically used as a wireless network card. I.e. a computer connects via Ethernet cable to the nano router and the TL-WR702N is used to access a wireless network.


At the relatively low price (US$19 to US$29 B&H, Newegg, Amazon, ..) the size, data transfer rate, and feature-set, this is an impressive device. After running it for one week without the need for a reset, it’s now part of my travel backpack ..

TL-WR702N internal Web Server



  • Wireless Standards 802.11b, 802.11g, 802.11n
  • Interfaces 10/100Mbps WAN/LAN
  • Dimensions (WxDxH) 3.2 x 2.8 x 1.1 in (81 x 71 x 28mm)
  • Frequency 2.4-2.4835 GHz
  • Signal Rate 11n  Up to 150Mbps
  • Signal Rate 11g  Up to 54Mbps
  • Signal Rate 11b  Up to 11Mbps
  • Security 64/128/152-bit WEP / WPA / WPA2,WPA-PSK / WPA2-PSK


  1. Suberb device. I am going to purchase it for sure.

  2. I bought this router, and everything is fine except that I have to reboot it every hour, because it just stops working, I tried every version of official firmware, and it’s all the same, and also you can’t flash OpenWRT on it, because it only have 2mb of memory, but I guess you can’t complain for that price, also it comes with micro USB cable, and AC usb adaptor, which by itself worth that 20 bucks, but if you need a good reliable WiFi router, that is not your best choice

  3. Hey HeadCracker are you powering it with usb? If so check your power save settings on the port.

  4. I experienced the same sporadic connectivity problems and need for resets as well.

    Even with no power-saving features enabled within my BIOS, or in Windows, the device still had issues. I have a high end motherboard and power supply with plenty of room to add powered devices.(only a few USB 2.0 / 3.0 or ESATA ports being used in my scenario)

    After some troubleshooting, I suspected that the USB 2.0 ports were not delivering enough, consistent, low-latency power to the pocket router. When I tested this with my USB 3.0 ports, the problem was solved and my local wifi speeds increased exponentially. Once I checked the micro power supply/adapter, I was surprised to see a 1.0A output powering a USB device. Consider this same 1.0A power draw would be rather demanding on the old USB 2.0 bus.

    For max, clean performance of this device, I highly recommend you utilize the power adapter that came with it, or a USB 3.0 port at a minimum.

  5. I have one of these and always run it from the mains/USB converter it came with, yet still find it crashes every couple of days. Shame, because the reliability is the only fault I can find with it.

  6. I could not get it to function as a client. Has anyone else had issues with this? It did not appear to pass the DHCP through. I was a little disappointed by the lack of status info available.

  7. We carry these around with us everywhere we go (security system technicians) they work perfectly except for client mode! Ive tried everything… No luck

    @Tim… Any updates? You had any luck at all with client mode?

  8. I use this in client mode for my 1st gen xbox360, 20 bucks instead of 60/70 that microsoft asks for its wireless adapter. Works great, but I setup it with a fixed ip address, so I have not tested the dhcp throuh issue.

  9. I just bought this router specifically for use in client mode. It seems to work ok in default, but in client mode it will not connect to my existing wifi router.

    Would love to know if there’s something stupid I’m not trying or if there is a genuine problem with this model. I’m using a mac running Mavericks btw, although the client mode is in theory for connecting my smart tv to the wifi.

Submit a Comment

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>